Skip to content
Rear wing and black rear deck of a Porsche 911 GT3 RS under hexagon LED shop lights at Brookswood Tint in Langley

Paint protection film · Acura Integra

Acura Integra PPF in Langley, BC

At a glance

LLumar Platinum paint protection film on an Acura Integra starts at $850 for Partial Front at Brookswood Tint, $1,550 for Full Front, $1,900 for the Track Package and $4,000 for Full Vehicle. The Type S needs its own patterns, because Acura says every body panel ahead of its A-pillars is unique to that model. The final figure depends on the trim, the panels you pick and the state of the paint.

Partial Front
From $850
Full Front
From $1,550
Track Package
From $1,900
Full Vehicle
From $4,000
Type S body
2.8 in wider, own front panels
Parking sensors, 2026
Elite A-Spec and Type S

How much is PPF on an Acura Integra?

The four packages start at $850, $1,550, $1,900 and $4,000 in LLumar Platinum. Those are the shop’s starting prices; a Type S, extra panels or paint that needs correcting before film can raise the quote.

Package Integra panels covered From
Partial Front Front bumper, leading edge of the hood and fenders, headlights, mirrors $850
Full Front Entire hood, both fenders, front bumper, headlights, mirrors $1,550
Track Package Full Front, the A-pillars, the rocker panels and a section of roof $1,900
Full Vehicle Every painted panel, plus the headlights $4,000

Platinum is a self-healing film: light swirls in the top coat close up with warmth. LLumar backs it with a 10-year manufacturer’s limited warranty, and the shop’s published warranty wording names yellowing, cracking, bubbling and peeling. Before any film goes down, the paint is decontaminated and, if it needs it, corrected. The Full Front package page shows that coverage in detail.

Why does a Type S need different film patterns?

Because the body is different from the windshield forward. Acura’s Type S launch release says “every body panel forward of the A-pillars is unique to Type S”, and that the car is 2.8 inches wider than the standard Integra with “boldly flared wide body fenders”.

The same release lists a vented aluminum hood, a larger open grille, a wider lower opening for the intercooler and functional ducts in the front fascia that route air to the brakes. Each vent and duct is an edge the film has to finish around, and a blistered fender is a deeper curve to stretch over than a flat one. Film for a Type S comes from Type S patterns, so name the trim when you ask.

At the back, Acura added a gloss black diffuser and a decklid spoiler. Those sit outside the front packages; Full Vehicle covers the painted rear surfaces if you want them protected too.

What did the 2026 refresh change at the front of the Integra?

The A-Spec gained an aero kit, and some colours gained a body-colour grille. Acura’s August 2025 on-sale release says the kit “adds bodycolor side spoilers to each corner of the front fascia and a sleek new side sill garnish”.

Spoilers on the bumper corners sit right where stones thrown off the car ahead land, so on a 2026 A-Spec they belong in the bumper pattern. The new side sill garnish runs along the rocker, which only the Track Package and Full Vehicle reach. Acura’s refresh announcement also confirms the Integra’s hood is aluminum, and says Double Apex Blue Pearl and Performance Red Pearl cars now get a colour-matched grille.

Which colours and sensors does an Integra install work around?

Five colours and, on most trims, a set of parking sensors. Acura Canada’s 2026 Integra specifications list Platinum White Pearl, Majestic Black Pearl, Solar Silver Metallic, Urban Grey Pearl and Double Apex Blue Pearl, with the last two limited to the Elite A-Spec and Type S.

2026 Integra, Canada A-Spec Elite A-Spec and Elite A-Spec MT Type S
Parking sensors Not listed Yes Yes
Mirror housings Body-coloured Body-coloured, turn signals built in Body-coloured, turn signals built in
Exterior styling A-Spec design A-Spec design Type S design

Where the bumper carries sensors, the film is trimmed to sit around each one, and if a curve needs a relief cut the installer shows you where before laying the film. The mirror housings are body colour on every trim, and every package covers them. Gloss Platinum keeps the pearl and metallic paints looking as Acura finished them, while Platinum Matte gives any of them a satin finish.

How do you book Integra PPF in Langley?

Send the model year, trim and colour, and say which package you’re weighing. The shop replies with the starting price for your Integra, checks the paint when the car comes in, and explains any correction before you commit.

Partial Front usually takes one day, Full Front or the Track Package one to two, and Full Vehicle three to five. Ask through the Integra PPF quote form or call 604 534 6433. If the rest of your commute matters, PPF coverage for Highway 1 commuters compares the packages, and Integra window tint can be done on the same visit.

Drawing of a white sports coupe with the full hood, both front fenders, the front bumper, headlights and mirrors coloured green
Full Front coverage, from $1,550. The drawing is a coupe, not an Integra; your car is cut from Integra patterns.

Asked at the counter

Questions about acura Integra PPF

01Is PPF worth it on an Integra A-Spec that's driven on Highway 1 every day?

For a daily highway commute, Full Front makes sense, because it covers the whole hood and both fenders rather than the leading edge only. The bumper and headlights take most of the stone hits on any car.

02Does the Type S cost more to film than the regular Integra?

It can. The Type S has wider fenders, a vented hood and a different front fascia, so the patterns are larger and more shaped. The shop confirms the figure once it knows the trim.

03Can I get matte PPF on a gloss Integra?

Yes. LLumar Platinum Matte gives gloss paint a satin finish on every panel it covers. Decide before the film is cut, since it's a different product from the gloss film.

04How soon can I wash the Integra after the film goes on?

Give it a week first, as the shop advises. After that, hand wash or use a touchless bay, and keep pressure-washer nozzles off the film's edges.

Get a quote today.

Call or text 604.534.6433, email us, or send the form and we'll come back with a price and a date.